SpeakerCraft ASM/ELT01300 Manuel d'instructions télécharger pdf (Page 2)

PRINTER’S INSTRUCTIONS:

INSTR,INSTL,IRC-3.0 • LINEAR P/N: 223485X20 • INK: BLACK • MATERIAL: 70 LB. GLOSS WHITE COATED PAPER • SIZE: 11.000” X 8.500” FOLD TO 5.500” X 8.500” • FOLDING: 1 FOLD VERTICAL, FINISH WITH LOGO SHOWING • SCALE: 1-1

223485X20 • IMAGE 2

IR OUT

ST IN

GND

+12V

IRC-4.0

J-BOX

IR RECEIVER

SpeakerCraft

To 120V AC

(unswitched)

PS-1.0

Power

Supply

A/V Receiver

Satellite

DVD

AT-1.0

Amplified Terminator

IRC-3.0

Shelf Top IR Receiver

IRC-3.0

Shelf Top

IR Receiver

IRE-1.0

Emitter

IRE-3.0 Visible Emitter

ROOM 1

ROOM 2

ROOM 3

PS-1.0

"STATUS"

Supply

To Switched

AC Outlet on

A/V Receiver

IRE-4.0

Dual

Visible Emitter

To Additional

Controlled Unit

Rear View

Add Resistor at each IR resistor

to reduce STATUS brightness,

if desired. See text.

Striped

Side

STATUS

+12V

GND

IR OUT

STATUS

(yellow)

+12V

(red)

GND

(black)

IR OUT

(white)

Note: Remove Plug,

strip leads and use

terminals as shown.

See text.

EZ-Connect Terminals

+12V

GND

ST OUT

IR IN

RCVR

STATUS IN

5~24V DC

12V DC

REGULATED

BL ON

NET ON

EM ON

EMITTERS /

BLASTERS

EMITTERS

NET OFF

AT-1.0

AMPLIFIED

TERMINATOR

SpeakerCraft

IRC-4.0

J-Box IR Receiver

IRC-2.1

Surface Mount IR Receiver

CONTROLLED COMPONENTS AREA, MAIN ROOM, ETC.

• Power: 12V DC @ 6 mA. Supplied from connected Terminator.

• IR Lens rejects visible light interference.

• Crosshatch Shield (internal) inhibits EMI/ESI Interference.

• Carrier Frequency Acceptance Range: 28 to 90 kHz.

• Control Range: Up to 35 feet, depending on remote strength and ambient noise conditions.

• Control Angle: ±50˚ off axis.

• Dimensions: 3

⁄16" (81mm) W x 1

⁄8" (28mm) H x 1

⁄16" (27mm) D.

SYSTEM CONNECTIONS

The following are a few typical applications of the IRC-3.0 in IR repeater systems.

A Basic System

Fig. 2 shows a basic plug-and-play installation, such as controlling components that are

behind closed cabinet doors or in a nearby closet.

single run. If using shielded wire, these lengths would be reduced by approximately

30%. Also, to achieve operation with long lengths, the lower DIP switch on the

AT-1.0

must be set to the NET ON position.

2. Connect IR receivers in each room to the 4-conductor home runs as shown, using the

4-conductor terminal strip supplied.

Note: To connect an IRC-3.0 as shown in Room 3, you will need to cut off the

4-conductor plug, strip the leads and make connections to the inter-room wire using

a 4-conductor terminal strip (not supplied), as shown. See also Fig. 1 for wire color

identiﬁcation. Contact SpeakerCraft Technical Support to obtain the terminal strip.

To 120V AC

(unswitched)

PS-1.0

Power

Supply

A/V Receiver

Satellite

DVD

AT-1.0

Amplified Terminator

IRC-3.0

Shelf Top

IR Receiver

IRE-3.0 Visible Emitter

IRE-3.0

Visible Emitter

IRE-3.0

Visible Emitter

Remote Control

+12V

GND

ST OUT

IR IN

RCVR

STATUS IN

5~24V DC

12V DC

REGULATED

BL ON

NET ON

EM ON

EMITTERS /

BLASTERS

EMITTERS

NET OFF

AT-1.0

AMPLIFIED

TERMINATOR

SpeakerCraft

Fig. 3

1. Place the IRC-3.0 on a shelf top, a cabinet or other horizontal surface.

2. Plug the IRC-3.0 and Emitters into the SpeakerCraft AT-1.0 Ampliﬁed Terminator, as shown.

3. Set the DIP switches on the AT-1.0 to EM ON and NET ON or OFF.

4. Plug in the Power Supply.

5. The remote control, ﬁred at the IRC-3.0, should now control the components.

A Multi-Room System

Fig. 3 is an example of the IRC-3.0 functioning as a wired IR receiver in a multi-room system

with other SpeakerCraft IR receivers in various rooms, plus a local IRC-3.0. These control the

various components in the main room or equipment area.

1. Pull 4-conductor wire from each room (home runs) to the AT-1.0 Terminator near the

controlled components.

Note: Use 24 gauge unshielded solid or stranded copper wire up to 1200' (Cat. 5e

ok), 22 gauge up to 2000', 20 gauge up to 3000' and 18 gauge up to 5300'. Total

lengths include all wire runs from each room added together, not just the longest

2 3

Fig. 2

1 2

SmartPath 1
SYSTEM CONNECTIONS 2

Commentaires sur ces manuels

Pas de commentaire

SpeakerCraft ASM/ELT01300 Manuel d'instructions Page 2

Commentaires sur ces manuels

Produits connexes et manuels pour Récepteurs AV SpeakerCraft ASM/ELT01300